My computer keeps updating shut down best absolutely online dating sites

Hello everyone, First of all, I want to state I really don't know too much about computers.

I know a little but I really don't know all the names/fuctions/etc.

Most people never see this because they replace a computer before the battery goes dead. I downloaded a windows update for Windows Vista at start of May which didn't seem to complete to part 3.

The computer crashed up start up stating that a recent update was to blame. And choose to restore before the installation was launch. I have tried safe mode and safe with networking, I still cannot get onto my laptop in order to go to system restore. I have tried all options on starting the computer, and it just goes back to configuration. This is really pissing me off, as there are very important documents on here.

After doing this for several minutes it tells me that it must restart and to click "Finish" to restart.

I do so and my computer restarts and then loops right back to the Installing Updates screen and once again, after completing Step 1 or Step 2 it restarts and goes to the Loading Files screen and then to the Windows cannot start and the the repair scan.

It looped like this all night long and then again was doing it this morning when I left for work.

Any advice/suggestions would be greatly appreciated! Opearating System: Windows Vista Also, I don't really know how to do a System Restore and am concerned I will loose all my files.

my computer keeps updating shut down-57my computer keeps updating shut down-60

After completing the first and sometimes the second step, my computer will suddenly restart again and then the screen with state "Loading Files" and then come up with a screen that says Windows could not start and that it is scanning the files to repair.

knock wood, so far so goodmy Packard Bell Easy Note came with vista, and ive been installing updates for ages. I noticed a couple of interesting things, and now I have my computer back--I thought it was dead forever. If you shut your computer down when you see the "Configuring Updates" screen, when you boot up again you will see the useless options to boot in safe mode. If you shut your computer down shortly after you start it up, you should get different options: to either Launch Repair, or to Start Windows Normally. But by the third time I tried it, about 30 seconds in it asked me if I wanted to do a System Restore. It immediately skipped back to Configuring updates, and got stuck in the loop. I got back into Launch Repair and did the same System Restore, but this time I didn't wait for the blue screen to load up. It just seems to be a matter of major patience and not giving up--your computer is not wrecked. Hi guyz, Its really bad to see that computers come up with probs after you install updates.. go to control panel and select view installed updates and uninstal the updates that was instaled on the date your comp started coming up with the issue. Im trying to restore it as you say with different modes,but does not work. and then I pick the earliest restore point and it worked link to vista restore link to utorrent hope this helps YEAAAA!!! now the only option is to restore to the point bfore installing the windows update??? I was updating a Vista system that didn't even have SP1 installed. click next, then a screen of lists should come up click the SECOND one. hit F8 during boot, select repair computer at the top and then I did a system restore to 2 days ago, right before the auto windows update ran and F-ed everything up.

I recently installed some more updates but my laptop ran out of battery halfway through configuring. I shut the computer down shortly after starting it up, and if I recall correctly, it was at that point that I was offered a whack of new options. Restart the computer and should work fine, if its because of the update Try this should work fine... Get stuck configuring the stage 3,then the laptop shut down,shut on and again the same screen trying to configure the damn never star up,i can do anyhing at all,and dowload a windows repair tools, but doesn work neither. After updating to SP1 computer rebooted, but while booting up it got blue screen of death. it should have you do stuff to do like a scan and then you restart it then it works, NO MONEY OR NOTHING! Things looks good but my Norton IS is having some issues, and when I hit the fix now button it doesn't fix it....

However even loading from DVD has failed to rectify the problem and Microsoft have washed their hands of it so I have to find a computer engineer to hopefully recover my data. What if you did the Last Known Good Config and that didn't work? This happened once already but Im not sure how I corrected this.

My advice is NEVER NEVER LOAD A WINDOWS UPDATE as there is no guarantee they can adversely affect your computer and end up crashing it losing your data forever.! I read some where else that if you install the Vista SP1 Service Pack and then try to install your updates after that, it would work. I had disabled automatic updates (hoping to avoid this problem again) but it seems to still be running updates automatically.

Leave a Reply